Elastomeric Exterior Wall Paint

Theoretical paint consumption (30μm dry film)
10㎡/L/layer (the actual amount varies slightly due to the roughness and porosity of the base layer).

Dilution
Diluting with water is not recommended.

Surface condition
The surface of the base material should be flat, clean, dry, firm, free of oil, water leakage, cracks, and loose powder.

Coating system and coating times
♦ Clean the base: remove the residual slurry and unstable attachments on the wall, and use a spatula to shovel the wall, especially the corners of the window frame.
♦ Protection: Protect door and window frames, glass curtain walls, and finished and semi-finished products that do not require construction before construction to avoid pollution.
♦ Putty repair: This is the key to base treatment. At present, we often use waterproof exterior wall putty or flexible exterior wall putty.
♦ Sandpaper grinding: When sanding, it is mainly to polish the place where the putty is connected. When grinding, pay attention to the technique and follow the operating specification. Use water emery cloth for sandpaper, and use 80 mesh or 120 mesh water emery cloth for sanding the putty layer.
♦ Partial putty repair: After the base layer is dry, use putty to find unevenness, and the sand will be flat after drying. The finished putty should be stirred well before use. If the putty is too thick, you can add water to adjust it.
♦ Full scraping putty: Put the putty on the pallet, scrape it with a trowel or squeegee, first up and then down. Scrape and apply 2-3 times according to the condition of the base layer and decoration requirements, and the putty should not be too thick each time. After the putty is dry, it should be polished with sandpaper on time, and it should not be wavy or leave any grinding marks. After the putty is polished, sweep away the floating dust.
♦ Primer coating construction: use a roller or row of pens to evenly brush the primer once, be careful not to miss the brush, and don't brush too thick.
♦ Repair after painting the anti-alkali sealing primer: After the anti-alkali sealing primer is dry, some small cracks and other defects on the wall will be exposed due to the good permeability of the anti-alkali sealing primer. At this time, it can be repaired with acrylic putty. After drying and polishing, reapply the anti-alkali sealing primer to prevent the inconsistency of the absorption effect of the opposite paint due to the previous repair, thus affecting its final effect.
♦ Topcoat construction: After the topcoat is opened, stir evenly, then dilute and stir evenly according to the ratio required by the product manual. When color separation is required on the wall, first pop out the color separation line with a chalk line bag or ink fountain, and leave 1-2cm of space at the cross-color part when painting. One person first uses a roller brush to dip the paint evenly, and the other person then uses a row brush to flatten the paint marks and splashes (spraying construction method can also be used). The bottom and flow should be prevented. Each painted surface should be painted from the edge to the other side and should be finished in one pass to avoid seams. After the first coat is dry, apply a second coat of paint.
♦ Completion cleaning: After each construction, rollers and brushes should be cleaned, dried and hung in the designated position. Other tools and equipment, such as wires, lamps, ladders, etc., should be taken back in time after the construction is completed, and should not be placed randomly. Mechanical equipment should be cleaned and repaired on time. After the construction is completed, keep the construction site clean and hygienic, and the contaminated construction sites and equipment should be cleaned up on time. The plastic film or tape used to protect the wall should be cleaned before dismantling.

Tool Cleaning
Please use clean water to wash all utensils on time after stopping in the middle of painting and after painting.

Packaging
specification 20KG

Storage method
Store in a cool and dry warehouse at 0°C-35°C, avoid rain and sun exposure, and strictly prevent frost. Avoid stacking too high.